Innovacorp is a manufacturer, exporter, and supplier of paper chemicals in Greater Noida NCR. Our range covers wet-end chemicals, sizing agents, strength additives, retention aids, and process control chemicals for paper and board mills in the NCR belt — including Muzaffarnagar, Meerut, Saharanpur, and Yamunanagar.

Why Paper Mills in the NCR Belt Need a Different Chemical Approach

Paper mills in the NCR belt work with a different furnish mix than coastal mills. A large share of the waste paper comes from Delhi NCR's collection network, which means the incoming stock varies more from lot to lot — and the variation is sharper than what a mill in Tamil Nadu or Gujarat sees.

That variation shows up at the wet end. Retention drops on some lots. Sizing response shifts. Pitch and slime load changes with the season. A chemical programme that worked last month may not hold this month. The fix is not one stronger product — it is a grade that matches the furnish you are actually running.

Where Our Paper Chemicals Are Used

Our range maps to the main wet-end and process stages in an NCR paper mill:

• Stock preparation: retention and drainage aids that help capture fine fibers and filler on the wire, especially on high-ash waste paper furnish.
• Wet-end sizing: AKD (Alkyl Ketene Dimer) and rosin-based sizing agents for water resistance and ink holdout on writing and printing grades.
• Strength development: dry strength and wet strength resins for packaging and board grades.
• Pulping and bleaching: surfactants and aids that support lignin removal and brightness development in your existing bleaching sequence.
• Process control: defoamers and biocides for pitch, foam, and slime control in the stock and white water loops.

Types We Manufacture, Export & Supply in Greater Noida NCR

Each grade is built for a specific stage, so your process team can map it to the machine without guesswork:

• Sizing agents: AKD and rosin-based, for surface and internal sizing.
• Retention and drainage aids: for fine particle retention and faster water drainage on the wire.
• Strength additives: dry strength and wet strength resins.
• Pulping and bleaching aids: surfactants for lignin removal and brightness development.
• Process control chemicals: defoamers and biocides for pitch and slime control.

Specification

Property	Typical Value
Appearance	Clear to milky liquid (grade dependent)
pH (as supplied)	3.0–7.0 (grade dependent)
Active content	15–30% (grade dependent)
Density	0.98–1.05 g/cm³
Solubility	Dispersible in water; use as supplied or pre-diluted
Shelf life	12 months in unopened container

Final specification is confirmed after a lab or plant trial on your furnish and machine.

Application and Dosage

Dosing depends on furnish type, machine speed, and target paper grade. As a working starting range for NCR mills:

• AKD sizing: 0.10% to 0.30% on dry fiber, adjusted for target Cobb value.
• Retention aids: 200–600 g/tonne on dry fiber, set by trial.
• Dry strength resins: 0.5% to 1.5% on dry fiber.
• Defoamers: 50–200 ppm on stock, set by foam load.
• Biocides: dosed by white water volume and slime load, set by trial.

Final dosage is confirmed after a plant trial on your machine.

Packing

We supply in four pack sizes for mill and central-store use:

• 35 kg HDPE carboy
• 200 kg HDPE drum
• 1000 kg IBC tank
• Bulk tanker on request for high-consumption grades

Key Benefits

The reason NCR mills move to our range is not one headline feature. It is small gains that add up over a production run:

• Furnish-matched grades: we review your furnish mix, retention, and drainage before recommending a grade — especially important when waste paper quality varies.
• Grade-specific formulations: separate AKD, rosin, retention, strength, and process-control grades, so the right product goes to the right stage.
• Documented dosage: TDS states the working range for each grade, so your process team can build the trial plan.
• Packing for mill scale: carboys, drums, and IBCs, plus bulk tanker on request.
• Documentation: TDS and MSDS available for each grade on request.

Technical Support

We work with paper mill process teams in the NCR belt — Muzaffarnagar, Meerut, Saharanpur, Yamunanagar — on wet-end audits before recommending a grade. Share your furnish mix, machine speed, target paper grade, and current chemical programme, and we will recommend grades and dosages for a plant trial on one machine before you roll out across the mill.

Frequently Asked Questions

How do retention aids improve productivity in Greater Noida paper mills?

Retention aids help bind fine fibers and fillers to long fibers, which supports faster drainage on the wire, better paper formation, and reduced fiber loss to white water. The actual gain depends on your furnish, machine speed and current dosing — a plant trial is the best way to confirm it.

What is the benefit of AKD sizing in packaging paper production?

AKD (Alkyl Ketene Dimer) sizing provides alkaline sizing for packaging boards, supporting water resistance and surface strength. The grade and dosage depend on your furnish and target Cobb value — we recommend a starting grade after a plant walk-through.

Which paper chemicals does Innovacorp supply in Greater Noida NCR?

Innovacorp manufactures, exports and supplies AKD sizing agents, retention aids, wet strength resins and deinking agents for paper and board mills in Greater Noida NCR and the surrounding belt — including Muzaffarnagar, Meerut, Saharanpur and Yamunanagar. Grades differ in active content and application stage — share your furnish type and machine details and we will confirm the grade.

Do you ship paper chemicals outside Greater Noida NCR?

Yes. We supply across India and to selected export markets. Packing options and delivery timelines depend on the grade and quantity — call +91-9312871070 to confirm.

For TDS, MSDS and a quote, call +91-9312871070.